Posts
389
Comments
117
Trackbacks
40
Mini ITX Experiences

My little server has been running fanless for about a week now and is running reliably beside the router, tucked in a corner and casting an eerie blue light at night from the power switch.

Just to review, the bits I used were:

It took me about a day to build the thing, thinking back I haven't actually ever built a complete PC before, so I'm not the fastest. I had all the bits needed, the best bit being the case which comes with a laptop style cable and transformer, a built in power supply and adapters for the 2.5 hard disc drive and slim DVD drive - both of which have ide connections different to big PC's.

The trickiest bit was getting over the hurdle of getting the motherboard to fire up. It just wouldn't do it to begin with, and the fix just appeared to be to try things step by step. I purchased the IO plate which fills the hole in the back of the case, but in the end didn't use it once I got it running. So first lesson learned, don't assume the mobo is dead until you have tried the various components. The mobo will pause from time to time too, so it is a case of loosing screws off, unplugging the power supply and trying again. I hadn't got anything to base my expectation on so hearing the reassuring beep (I still don't know where the actual beeper is) tells me all is well. There is also a proper procedure for resetting the bios, which is only in the most recent manual on the VIA website.

The other lesson learned is that for some reason the Sony and Seagate drives didn't want to play master and slave on the same IDE channel, trying all the combinations of jumper leads and whatever didn't work so I ended up with the two drives on seperate interfaces. I've read posts on the internet to this effect about the funny ide lead that has to be used for the 2.5 HDD, but in the end I had to use another IDE lead for the Sony Optical drive. Interestingly the Morex 377 case comes with an adapter plate that fixes to the back of the slimline drive, so that a standard PC type IDE cable can be used. I connected up the case fan for the safest approach to temperature for the first few days, although the case itself features a fair amount of metal which must act to dissipate heat.

As there isn't any floppy drive, you have to boot the O/S from either the CD, network card or usb, which are all choices in the bios. The install part went no problem at all.

When I had the machine in place at home, the fan noise was noticable, not as loud as my old PS2, but a new noise nonetheless. But keeping an eye on it over the next few days showed it was blowing cold air, so I disconnected it. I had a wee problem with the network disappearing, but this was cured by pulling the power supply out of the back, rather than just using the power switch.

It has been running quite happily as a wee proxy server for over a week now, with just power and network plugged in to it, case fan disconnected, but sat on its wee foot. It runs along quite nicely, performing quite well for a 533Mhz processor. It is also very quiet, for some reason the disc drive is practically inaudible.

Lesson Summary:

  • You will hear a single beep when it boots up, this is good. The fan will spin up regardless.
  • For whatever reason my motherboard didn't see the whole 512Mb of a single ram chip, just seeing 256 of it, so I bought another two 256Mb chips for the two slots.
  • For whatever reasons the 2.5 HDD and Slimline DVD Rom didn't like sitting on the same channel. Disconnect either, and the other would pop up in the BIOS.
  • Mini ITX terminology is strange, "Power Supply" is actually the component that converts the voltage coming in to the case to a regulated amount feeding the molex connector to the motherboard. It mounts just behind the front panel of the case. The plastic brick with a plug on the end is something else.
  • Both the motherboard and case come with a number of very useful cables and fitting parts as standard, but these may be missing if you buy from ebay. E.g. I just received the motherboard, whereas it normally comes with cables and IO plate etc. The case comes with a foot, 240v adapter, cd-rom adapter, various screws and fittings etc.
  • The Mini-ITX format is tiny, the complete machine is only slightly bigger than my Netgear router.
  • 2.5 Drives have strange connectors, so read the specs very carefully to check between SATA and UATA!!
  • Everything is a very very tight fit inside the case, I literally had to squeeze it all in, but it all runs ok.
  • I still haven't figured out how to flash the motherboard bios without a floppy disc drive - usb perhaps?

I checked with my old colleage Bart and apparently I can get some geek points for finally having a server.

posted on Friday, December 22, 2006 8:24 AM Print
Comments
No comments posted yet.

Post Comment

Title *
Name *
Email
Url
Comment *  
Please add 3 and 4 and type the answer here: